1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
//! Async I2C API
//!
//! This API supports 7-bit and 10-bit addresses. Traits feature an `AddressMode`
//! marker type parameter. Two implementation of the `AddressMode` exist:
//! `SevenBitAddress` and `TenBitAddress`.
//!
//! Through this marker types it is possible to implement each address mode for
//! the traits independently in `embedded-hal` implementations and device drivers
//! can depend only on the mode that they support.
//!
//! Additionally, the I2C 10-bit address mode has been developed to be fully
//! backwards compatible with the 7-bit address mode. This allows for a
//! software-emulated 10-bit addressing implementation if the address mode
//! is not supported by the hardware.
//!
//! Since 7-bit addressing is the mode of the majority of I2C devices,
//! `SevenBitAddress` has been set as default mode and thus can be omitted if desired.

pub use embedded_hal::i2c::Operation;
pub use embedded_hal::i2c::{
    AddressMode, Error, ErrorKind, ErrorType, NoAcknowledgeSource, SevenBitAddress, TenBitAddress,
};

/// Async i2c
pub trait I2c<A: AddressMode = SevenBitAddress>: ErrorType {
    /// Reads enough bytes from slave with `address` to fill `buffer`
    ///
    /// # I2C Events (contract)
    ///
    /// ``` text
    /// Master: ST SAD+R        MAK    MAK ...    NMAK SP
    /// Slave:           SAK B0     B1     ... BN
    /// ```
    ///
    /// Where
    ///
    /// - `ST` = start condition
    /// - `SAD+R` = slave address followed by bit 1 to indicate reading
    /// - `SAK` = slave acknowledge
    /// - `Bi` = ith byte of data
    /// - `MAK` = master acknowledge
    /// - `NMAK` = master no acknowledge
    /// - `SP` = stop condition
    async fn read(&mut self, address: A, read: &mut [u8]) -> Result<(), Self::Error> {
        self.transaction(address, &mut [Operation::Read(read)])
            .await
    }

    /// Writes bytes to slave with address `address`
    ///
    /// # I2C Events (contract)
    ///
    /// ``` text
    /// Master: ST SAD+W     B0     B1     ... BN     SP
    /// Slave:           SAK    SAK    SAK ...    SAK
    /// ```
    ///
    /// Where
    ///
    /// - `ST` = start condition
    /// - `SAD+W` = slave address followed by bit 0 to indicate writing
    /// - `SAK` = slave acknowledge
    /// - `Bi` = ith byte of data
    /// - `SP` = stop condition
    async fn write(&mut self, address: A, write: &[u8]) -> Result<(), Self::Error> {
        self.transaction(address, &mut [Operation::Write(write)])
            .await
    }

    /// Writes bytes to slave with address `address` and then reads enough bytes to fill `read` *in a
    /// single transaction*.
    ///
    /// # I2C Events (contract)
    ///
    /// ``` text
    /// Master: ST SAD+W     O0     O1     ... OM     SR SAD+R        MAK    MAK ...    NMAK SP
    /// Slave:           SAK    SAK    SAK ...    SAK          SAK I0     I1     ... IN
    /// ```
    ///
    /// Where
    ///
    /// - `ST` = start condition
    /// - `SAD+W` = slave address followed by bit 0 to indicate writing
    /// - `SAK` = slave acknowledge
    /// - `Oi` = ith outgoing byte of data
    /// - `SR` = repeated start condition
    /// - `SAD+R` = slave address followed by bit 1 to indicate reading
    /// - `Ii` = ith incoming byte of data
    /// - `MAK` = master acknowledge
    /// - `NMAK` = master no acknowledge
    /// - `SP` = stop condition
    async fn write_read(
        &mut self,
        address: A,
        write: &[u8],
        read: &mut [u8],
    ) -> Result<(), Self::Error> {
        self.transaction(
            address,
            &mut [Operation::Write(write), Operation::Read(read)],
        )
        .await
    }

    /// Execute the provided operations on the I2C bus as a single transaction.
    ///
    /// Transaction contract:
    /// - Before executing the first operation an ST is sent automatically. This is followed by SAD+R/W as appropriate.
    /// - Data from adjacent operations of the same type are sent after each other without an SP or SR.
    /// - Between adjacent operations of a different type an SR and SAD+R/W is sent.
    /// - After executing the last operation an SP is sent automatically.
    /// - If the last operation is a `Read` the master does not send an acknowledge for the last byte.
    ///
    /// - `ST` = start condition
    /// - `SAD+R/W` = slave address followed by bit 1 to indicate reading or 0 to indicate writing
    /// - `SR` = repeated start condition
    /// - `SP` = stop condition
    async fn transaction(
        &mut self,
        address: A,
        operations: &mut [Operation<'_>],
    ) -> Result<(), Self::Error>;
}

impl<A: AddressMode, T: I2c<A>> I2c<A> for &mut T {
    async fn read(&mut self, address: A, read: &mut [u8]) -> Result<(), Self::Error> {
        T::read(self, address, read).await
    }

    async fn write(&mut self, address: A, write: &[u8]) -> Result<(), Self::Error> {
        T::write(self, address, write).await
    }

    async fn write_read(
        &mut self,
        address: A,
        write: &[u8],
        read: &mut [u8],
    ) -> Result<(), Self::Error> {
        T::write_read(self, address, write, read).await
    }

    async fn transaction(
        &mut self,
        address: A,
        operations: &mut [Operation<'_>],
    ) -> Result<(), Self::Error> {
        T::transaction(self, address, operations).await
    }
}